Tuning up for Pruning Up–Care, Maintenance and Utilization of Hand Pruning Tools

A. J. Downer

Fall is passing into winter and the bare sticks in my deciduous fruit orchard are calling to my annual fruit tree pruning chores.  I can prune my entire orchard with very few tools: a good pair of bypass clippers, a similar set of loppers

Illustration 1. Tri-edge saw blades are made from stainless steel and are not easily sharpened. When dull or bent they should be replaced.

(optional) and a high quality “razor” or “tri edge” saw.  Most hand tools require some maintenance especially the clippers and loppers.   Clippers are easily sharpened but modern saw blades can not be sharpened by gardeners. I usually just buy a new saw, replacing the old one when blade eventually dulls or bends from over zealous use (illustration 1).

Illustration 2. To sharpen bypass clipper blades follow the angle of the bevel. Do not sharpen the flat side of the blade

Before using your pruning tools inspect them for signs of damage. Blades should be sharp and straight.  Loppers should have their rubber “bumpers” intact otherwise your knuckles will be smashed after exerting force on a difficult branch.  Sharp tools offer less resistance and actually decrease injury to users. One exception here is with the modern “tri-edge” or “razor” saws. These saws can cut so quickly that you may pass through the branch you are cutting and continue on to some part of your anatomy quickly ripping your flesh open. I have suffered more cuts (some serious) from these saws than from any other gardening activity (although I was recently impaled by a frog metal art sculpture!).  They should be used with careful precision, not with the wild abandon and pruning fervor of the craven academic desperate for real world pruning experiences.  A thick long sleeved shirt and gloves will also help prevent cuts from hand pruning equipment.

Bypass clippers are so termed because the blade passes by the hook. To sharpen these, find the bevel on the edge of the clippers and align a small file to the same angle of this bevel, and file the bevel until you can feel the sharpness with your finger (Illustration 2).  Never sharpen the back side of the bevel—this will create a gap, and every time you cut, a flap of tissue will remain. Back bevel sharpened clippers will require blade replacement or grinding until the back bevel is gone. The hook does not require sharpening, do not attempt to file it. Repeat this process with lopper blades.

When you are done pruning for the day, wipe the blades of your clippers and loppers with an oil soaked rag or apply a few drops of oil and rub it into the blade. Most modern saws blades are made from stainless steel and require no oil protection.

As a Cooperative Extension Advisor, one of the most common questions I receive is: “Should I sanitize my clippers between cuts or between uses on various plants?”.  Indeed, many publications, extension leaflets, gardening columns, and other sources make broad recommendations to sanitize clippers after every cut. Some articles even compare various products for their killing efficacy.  Blind recommendations are often made to sanitize clippers when the pathogen is not  known or specified.  It is not necessary to sanitize your clippers when pruning most garden plants and fruit trees.  There are a few pathogens that are spread by moving plant debris, but published evidence that they are spread by hand pruning equipment (especially clippers) is nil. One exception is palm wilt caused by Fusarium oxysporum f.sp. canariensis which is easily spread by saws. Some of the canker fungi caused by Botryosphaeria can also be spread by pruning equipment. With many of these pathogens, a wound is required for infection so it may not be that the clippers are spreading disease so much as providing an entry point (infection court) so that pathogens have a way to enter.

If diseases are present in or near the plant already, sterilizing pruning equipment will simply provide a clean entry port for the pathogen—infection can still follow after the cut is made with a sanitized tool.

In my garden, I never sanitize clippers between cuts.  However, conditions vary across the US, and in some places rain, humidity, and temperature are more favorable for disease development.  If you have concern about spreading pathogens, prune during the dormant season, when the likelihood of pathogen activity is lowest. Apply dormant sprays containing copper to limit the onset of new fungal diseases that may enter pruning wounds.  If you still feel you need to protect wounds from dirty clippers I like to use the flame from a plumber’s torch to sanitize.  A few seconds along the cutting edge front and back kills all pathogens (Illustration 3).  The process is similar for a saw but efficacy is increased if the saw gullets are wiped clean with a cloth and then the flame applied. The only time I take these measures is when I know I am working with plants that can be inoculated by pruning (which is rare).


Illustration 3. A plumber’s torch will rapidly sanitize saws and blades when pathogens are present in plant tissues.

When pruning garden plants, there are a plethora of recommendations on how to make cuts. Rose experts have extolled the virtues of an angled cut so water runs away quickly, flush cuts used to be recommended by arborists as the highest quality cut. These examples are without research foundation. Cuts on woody plants should made to create the most circular exposure that leaves the smallest surface area possible. We abandoned flush cuts many years back because they cut into protective zones that limit decay in trees. Some gardeners feel compelled to cover their cuts with a pruning paint and there is a similar paucity of research to support this practice. Leave pruning wounds unpainted.

Published by

Jim Downer

Dr. Downer has 34 years of experience as a horticulture and plant pathology Advisor with the University of California Cooperative Extension in Ventura County. Dr. Downer’s academic training is from California Polytechnic Univ., Pomona, (BSc. horticulture & botany, 1981; MSc. Biology, 1983;. In 1998 he earned a Ph.D. in plant pathology, from University of California, Riverside. Dr. Downer’s research is focused on mulch, soil microbiology and disease suppression in mulched soils, diseases of shade trees and cultural practices to maintain landscape plants. Dr. Downer is a member of the American Society of Horticultural Science, the American Phytopathological Society, The International Soc. of Arboriculture, and the Western Chapter of the ISA, and the International Society for Horticultural Science. Dr. Downer is an Adjunct professor at California Polytechnic University in Pomona. Dr. Downer serves on the Board of the John Britton Fund for tree Research as the chair of the research advisory committee, and currently chairs the regional conference committee for WCISA. Dr. Downer has a love of shade trees, Shinrin roku (forest bathing/walking) tree work, wood working, horses, gardening, horticulture and the study of plants and their biology.

2 thoughts on “Tuning up for Pruning Up–Care, Maintenance and Utilization of Hand Pruning Tools”

  1. I appreciate the good advice contained in this article. Before buying my “tri-edge” or “razor” saw, I did not know it had a reputation for considerable injury to the user. I have learned. Now, I don’t even pick up the handle without wearing gloves. It sure cuts quickly however.

  2. Sorry but as a mechanical engineer I must disagree and discourage from using a blow torch to desinfect tools. This is not a good idea. The tooths of high quality saws are normally heat treated to make them harder and stay sharp longer.

    http://www.silkysaws.com/About-Us_2/Silky-Technology

    If you heat them up with a torch you will soften the teeth and they will become blunt much faster. The same is true for pruners.

Leave a Reply to Roland Roth Cancel reply